EZ-2B - Click here for the brochure.

PLEASE READ THESE INSTRUCTIONS CAREFULLY

Your EZ-2B electric gummed tape dispenser is completely assembled, except for the water bottle, bottle support, and tape roll center shaft, which have been packed separately for shipping.

1)     Lift Sliding Door #511 from its track, and remove the water tank and brush.  Wash the new brush with warm water and soap to get good moistening action.  Replace this assembly with the longer bristles of the brush toward the front of the machine.  Squeeze the sides of the brush together a little when sliding the tank and brush in to prevent the bristles from sticking out the sides of the tank and “wicking” water out of the tank.

2)     Insert the foot of Bottle Support #526 into the clip on the linkage cover on the left side of the machine.  (See diagram 1).

3)     Fill the water bottle preferable with warm water, and insert the tip of the cap into the tank filler hole.  Lean the bottle back into the bottle bracket.  (See diagram 2).

            (For download purposes pictures are "thumbnails".  Click on pictures to enlarge.)

4)     Adjust the (2) Tape Roll Guides #27 to accommodate the width of tape used.  Place Center Shaft #29 through the core of the tape roll, and place the ends of Center Shaft #29 in the notches on top of the Tape Roll Guides, so the tape is supported by, and rotates freely on, the Center Shaft.  The tape roll must ALWAYS be supported on the center shaft in this manner to feed the tape smoothly, and prevent jamming, and overloading the motor.

5)     Insert the smooth, flat, and square end of the tape between the Upper and Lower Rear Guide Plates #4 & 5 until the end of the tape just touches the back of Cut-off Blade #63.  Make sure the tape is centered and straight in the machine.

6)     Plug the power cord into a GROUNDED 115 volt outlet.

7)     Set the Timer Knob #17 to the desired length.  The numbers on the dial indicate the approximate number of feet that will be dispensed with each operation.

8)     TO OPERATE THE DISPENSER, simply press down on the top cover.  The machine will automatically shut off when the pre-set length of tape has been dispensed.  Longer, “random” lengths of tape may be obtained by holding Top Cover #502 down until the desired length is obtained.

TO ADJUST WATER LEVEL, loosen Screw #219 on the side of the water tank and position Adjusting Plate #23 to obtain correct water level.  Raise Adjusting Plate #23 if tape is too wet.  Lower it if more water is needed.

MAINTENANCE

Remove and wash the moistening brush with soap and water frequently to remove glue deposits, which may hinder the moistening action.

The Cut-off Blade #63 is designed for easy removal for cleaning, which should be done frequently to ensure proper cutting action, and to prevent jamming.  Fine steel wool or a scouring pad may be used to clean the blade.  The blade is VERY SHARP – handle it carefully!

UNPLUG THE POWER CORD before removing the blade.  Open the Top Cover #302.  Lift Weighted Guide Plate #9 to unhook its turned-up back edge from under Crossbar #33, and remove the plate.  Slip the blade off Rocker Arm #550.    To replace the blade, reverse this process, making sure the “FRONT” label faces the front of the machine.  Hook the upturned back edge of the Weighted Guide Plate is hooked under Crossbar #33, with the weight is on the top front of the plate.  The Weighted Guide Plate helps hold the blade in place.

To remove the Top Rear Guide Plate #5 for cleaning, or removing the last couple of inches from a roll of tape, simply remove the (2) Tape Roll Guides #27, and pull the Guide Plate straight back from under spring-loaded Cross Bar #31.  When replacing the Guide Plate, be sure to push it all the way forward so it snaps into place under Cross Bar.  The projections on each side rest on the bottom Rear Guide Plate, providing space for the tape to slide between them.

ADJUSTING THE BLADE CLEARANCE

The slot in which the blade moves must have the proper clearance.  If the slot is too narrow, the blade may stick.  If the slot is too wide, the tape may curl down before being completely cut off, so the end feeds down into the machine, causing it to jam.

To adjust the width of the slot:  Unplug the power cord.  Remove the Water Bottle, Sliding Door, Water Tank, and Weighted Guide Plate.  Loosen the (2) Screws #54 which hold the Bottom Front Guide Plate #10 (just in front of the Blade).  Move the Guide Plate forward or back to get the desired clearance.  The proper clearance is about one thickness of reinforced tape.  When the clearance has been set, re-tighten screws #54.  CAUTION—Do not tighten these screws so tightly that they strip the threads out of the aluminum side rails.

REPAIR POLICY

Machines sent to us for repair or adjustment must be well packed to prevent damage in shipment, which may result in additional repair costs.

Please give us a complete description of the problem.  This saves diagnostic time and reduces labor charges.  We need your name, address, and phone number.  Please tell us which parts, which you have NOT returned.  Parts not returned with the machine will be presumed lost, and replaced with new ones unless we are informed otherwise.